Shop page iconDownload page icon

Choose your language

Multi-storey housing pilot project made of LIGNO®

Design and building physics in perfection: 
showcase wood in multi-storey construction as well

Die beiden viergeschossigen Mehrfamilienwohnhäuser im Lauchringer Riedpark überzeugen mit Ästhetik, wohngesundem Raumklima und guter Akustik, dank nahezu ausschließlicher Konstruktion mit Lignotrend-Bauteilen und der Ausstattung mit einem ökologischen Wärmedämmverbundsystem der Firma Gutex.
Der dunkle Holzboden dieser Wohnung bildet einen aufregenden Kontrast zu der hellen, fein profilierten Decke aus Weißtanne und gibt der Wohnung einen edlen Touch.
Die hier verbauten Decken made of LIGNO®, sind nicht nur elegantes Designelement, sondern mit ihren exzellenten Schallschutzqualitäten für den Geschossbau prädestiniert.
Die neuen Wohnungen der mehrgeschossigen Holzbauten punkten mit simpler Eleganz und optimalen Raumqualitäten.
Die hellen Profildecken von Lignotrend kreieren eine dynamische Atmosphäre in den neuen, raumgesunden Wohnungen.
Die Räume kreieren mit ihrer simplen Eleganz den perfekten Grund für charakterstarke Möbel, wie hier der schwarze Klavierflügel und die dunkle Vintage-Sitzcouch.
Diese Wohnungen punkten nicht nur mit ihrem futuristischen Design, sondern sind auch funktionell von höchster Qualität, mit Qualitäten wie Schallschutz oder optimierter Raumakustik.
Die fein profilierter Decke aus Weißtanne bringt ein Stück Natur in das minimalistisch eingerichtete Wohnzimmer und sorgt gleichzeitig für eine optimale Raumatmosphäre.
Die hellen Wohnungen im Lachringer Riedpark punkten mit Schallschutz, Brandschutz, optimaler Akustik und hoher Designqualität.
In der minimalistisch eingerichteten Wohnung mit dunklen Möbeln kommt die Deckensichtseite aus fein profilierter Weißtanne von Lignotrend besonders gut zur Geltung.
Die weite helle Wohnung mit hellen Böden und weißen Wänden sorgt mit der fein profilierten LIGNO® Decke aus Weißtanne mit integriertem Absorber für optimale Raumakustik.

After innovations in the building regulations of Baden-Württemberg, finally also residents of multi-storey timber buildings can enjoy all the advantages they already know from healthy single-family houses in tim-ber construction. And so the two four-storey buildings in the Lauchringer Riedpark are urban showcase projects in wood, which convince with design aesthetics, a healthy living environment, good acoustics and sophisticated technical timber construction details as well as with best noise protection comfort. 

Configuration overview

Components used

  • LIGNO® Rippe Q3  |  Ceiling component

    Product code: LIGNO® Rippe Q3_230-290_r0_ssp_z53_p0_a50g_625-12-4_WTE_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Acoustic classic).

    Installation top

    _r0 Open, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _230-290 Medium span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z53 REI 60 High fire resistance

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a50g Integrated absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-12-4 Slat profile

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTE Silver fir, economy

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Rippe Q3  |  Ceiling component

    Product code: LIGNO® Rippe Q3_230-290_r0_ssp_z53_p0_a0_625-51-1_WTE_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Akcoustic classic).

    Installation top

    _r0 Open, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _230-290 Medium span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z53 REI 60 High fire resistance

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a0 Without absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-51-1 Closed surface

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTE Silver fir, economy

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Block Q3  |  Roof component

    Product code: LIGNO® Block Q3_230-290_rg0_s0_z26_p0_a0_625-621-4_WTS_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Acoustic classic).

    Installation top

    _rg0 Closed, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _230-290 Medium span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z26 REI 30 Fire resistance

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a0 Without absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-621-4 Closed surface

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTS Silver fir knotless, plain

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Block Q3  |  Roof component

    Product code: LIGNO® Block Q3_230-290_rg0_s0_z26_p0_a50g_625-20-4_WTS_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO® Acoustic classic).

    Installation top

    _rg0 Closed, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _230-290 Medium span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z26 REI 30 Fire resistance

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected. 

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a0 Without absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-20-4 Slat profile

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species. 

    Wood type

    _WTS Silver fir knotless, plain

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Uni Q3/HL  |  Wall component 

    Product code: LIGNO® Uni Q3-HL_110_625_NSi_gh_b0
    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Element height

    _110 mm 

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation. 

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _NSi Industrial quality

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gh Planed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _b0 Untreated

  • LIGNO® U*psi  |  Insulation joist

    Product code: LIGNO® U*psi F_n_200
    Insulation joist


    The lower the U-value of a component and the lower the psi value of the details, the less heat is lost.This is precisely where the U*psi® cross-laminated timber insulating uprights from Lignotrend come into effect:They implement high insulating thicknesses in natural timber and minimise thermal bridges.

    Insulation joist

    Fleece as chamber separation

Reference-related

Downloads

Project participants

  • Jörg Kaiser Architekturbüro

    Architect

    Hauptstraße 47
    79787 Lauchringen
     

    www.architektkaiser.de

  • Holzbau Amann GmbH

    Execution

    Albtalstraße 1
    79809 Weilheim

    www.holzbau-amann.de

  • Holzerei Loderbauer

    Execution

    Kapellenstraße 3
    79737 Herrischried

    www.die-holzerei.de

  • Maise Holzbau & Zimmerei

    Execution

    Stiegstraße 25
    79774 Albbruck

    www.holzbau-maise.de

  • Foto & Design Gröber GmbH & Co.KG

    Photographer

    Untere Haspelstraße 29
    79761 Waldshut-Tiengen

     

    www.foto-und-design.com

  • Related references

      Apartment house in Hofmatt

      Wood holds its own: fire protection, sound insulation, earthquake resistance - modern wooden buildings made of LIGNO®...

      4417 CH-Ziefen

      View
        titletitletitletitletitletitletitle

      Highest timber construction in South Baden 

      Special solutions for multi-storey construction with wood allow the building material to be used...

      79539  Lörrach

      View
        titletitletitletitletitletitle