Shop page iconDownload page icon

Choose your language

Klimaholzhaus:
passive house standard 

Energy efficiency to the power of two 

Bei diesem neu angebauten Klimaholzhaus made of LIGNO© sorgt eine das gesäumte Gebäude umgebende Dämmhülle für minimalen Energieverbrauch.
In dem großzügig verglasten Wohnbereich sorgen Holzboden und die akustisch wirksame Decke aus Weißtanne für ein warmes, gemütliches Raumgefühl.
Der Wohnbereich des Klimaholzhauses wird dominiert von einem ausladenden Bücherregal und durch die großen Fenster sitzt man beim Lesen fast direkt im Garten.
Der Koch-und Essbereich ist komplett in hellen Naturtönen gehalten, die runden Deckenleuchten verströmen ein warmes Licht.
Im Außenbereich werden Alt-und Neubau durch einen überdachten Holzvorsprung verbunden, der sich zu dem einladenden Außen-Sitzbereich öffnet.
Mit viel Feingefühl wurde der rund 100 Jahre alte Altbau am Kittsee saniert und um einen Anbau in Massivholzbauweise erweitert.

In the Austrian border town of Kittsee, an old building and a climate-controlled timber house in passive house standard are combined to form a single-family home.

Configuration overview 

Components used 

  • LIGNO® Rippe Q3  |  Ceiling component 

    Product code: LIGNO® Rippe Q3_150-210_r0_s0_z26_p0_a50g_625-12n25-4_WTL_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO Acoustic classic).

    Installation oben

    _r0 Open, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _150-210 Small span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z26 REI 30 Fire resistance

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected.

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a50g Integrated absorber 

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation.  

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-12n25-4 Slat profile "nature" 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTL Silver fir knotless, patterned

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Block Q3  |  Roof component 

    Product code: LIGNO® Block Q3_70-150_rg0_s0_z0_p0_a0_625-12n25-4_WTL_gb_buv
    Installation top


    Whether the element is open or closed at the top is determined by the area of application. If, for example, the element is to be filled with fill on site as a storey ceiling or roof terrace (LIGNO® Rippe Q3-x), its cavities are open at the top (feature _r0). To guide pipes at the top of the element, a cross grid (_r25, _r50) can be added to some superstructures. For roof superstructures, there is usually a flat closed finish _rg0 (LIGNO® Block Q-x, LIGNO® Block Q3-x or corresponding versions of LIGNO Acoustic classic).

    Installation top

    _rg0 Closed, without cross grid

    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _70-150 Low span

    Fire resistance


    If fire protection is required, an additional layer is added below the web area (for elements with strip profiles _z26, _z53, _z80, for elements with board profiles Akustik klassik _k50g). Their height determines the fire resistance duration of the cross-section from 30 to 90 minutes. The fire resistance must be statically verified. If there are no requirements, the standard versions _z0 or _k50l are to be selected.

    Fire resistance

    _z0 R0

    Cavity


    Panel designs with slat profiles and additional layer can be configured with an additional cavity (_p26, _p53) below the additional layer for installation guides, fixtures or to improve sound absorption. Cables laid there then do not penetrate the fire-protection layer. If required, the cavity is filled with insulating material (_p26mw, _p26ha) to improve acoustic absorption. If no cavity is necessary, the characteristic _p0 is selected.

    Cavity

    _p0 No cavity

    Room acoustics


    If the soffit of the element is to have a good sound-absorbing effect, the penultimate layer is configured as absorber _a50g. Otherwise, this layer is configured as a solid wood layer _a0.

    Room acoustics

    _a0 Without absorber

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation.  

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625-12n25-4 Slat profile "nature" 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _WTL Silver fir knotless, patterned

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gb Brushed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _buv UV-protection stain

  • LIGNO® Uni Q3  |  Wall component  

    Product code: LIGNO® Uni Q3_110_625_NSi_gh_b0
    Statics


    The height of the load-bearing webs of the element is variable and determined according to static requirements from load and span. Within the framework of this configurator, the selection is limited to four height ranges. A more precise definition is made later during pre-dimensioning or verification with the LTB-x calculation programme. Bulk volume and/or necessary space for installations can also be decisive for the height.

    Statics

    _110 mm 

    Profile


    The visible layer is profiled with joints. The code for profiling indicates in millimetres: Element width, strip width (rounded, from/to if applicable) and joint width (rounded) as well as a letter identification for variants, e.g. with chamfered strip edges or with additional height gradation.  

    Note: Some profiles indirectly cause exclusions for other configuration options.

    Profile 

    _625 

    Wood type


    Various wood species are available for the visible layer. For quality reasons, individual wood species cannot be configured for all profiles; for technical reasons, surface treatments are excluded for some wood species.

    Wood type

    _NSI Industrial quality

    Structure


    The face is subjected to a brushing _gb as standard, which produces a stronger or weaker structure depending on the type of wood and makes the surface less sensitive to scratches.  Alternatively, a smooth sanding _gs can be carried out, or on request a bandsaw cut _grimitated.

    Structure

    _gh Planed

    Treatment


    Depending on the type of wood, the optional application of a surface treatment is possible ex works. Individual colour finishes are always sampled for coordination. For elements in individual lengths, colour treatment is limited to max. 5 m length.

    Treatment

    _b0 Untreated

Reference-related 

Downloads 

Project participants 

  • Createrra s.r.o. 

    Architect

    Hrubý Šúr 15

    SK-90301 Senec

     

    www.createrra.sk/

  • DetailDom s.r.o.

    Execution

    Lamačská cesta 1736

    SK- 841 03 Bratislava

    www.detaildom.sk/

  • Bohumil Šálek

    Photographer

    Sedmokrásková 1845/4

    SK- 821 01 Ružinov

     

     

  • Related references 

      Holiday home on Lake Neukloster

      Four walls, large windows, a roof and lots of light wood: architecture can be so simple and just...

      23992 Nakenstorf

      View
        titletitletitletitletitletitletitletitle

      Klimaholzhaus:
      Cube Alpnach

      When Waser Holzbau AG was awarded the building contract, there was still a wooden house from the 1970s...

      6055 CH-Alpnach

      View
        titletitletitleDer Esstisch befindet sich vor einer bodentiefen Fensterfront, die beim Essen den Blick ins Freie öffnet und Natur mit Innerem verbindet.titletitletitle